微波合成含氮掺杂碳量子点改性水性聚氨酯的制备与性能

以柠檬酸和尿素分别为碳源和氮源，微波法合成含氮掺杂碳点N-CDs。以异氟尔酮二异氰酸酯（IPDI）、聚氧化丙烯（PPG-2000）为主要原料，加入不同量的N-CDs制备一系列碳点水性聚氨酯复合材料 （N-CDs/WPU）。通过FTIR、TEM、XPS、UV-vis、荧光光谱和力学性能测试等对复合材料结构和性能进行表征。测试结果表明N-CDs主要由碳氮氧元素组成，表面具有胺基、羟基等活性基团，N-CDs的加入，提高了复合胶膜的力学性能，赋予了胶膜荧光性能。当N-CDs质量分数为0.6%时胶膜拉伸强度达到最大35.00MPa，加入量质量分数为0.8%时荧光强度最佳。     

基于3D打印技术制造柔性传感器研究进展

与传统的涂覆、沉积等加工手段相比，使用3D打印技术可制造复杂立体功能结构的传感器，将3D打印与柔性传感技术结合可以促进未来生物医疗、人工智能等领域的发展。本文介绍了国内外基于3D打印技术制造柔性传感器的最新进展，其中包括聚酰亚胺等多种基底材料、纳米金属等多种打印传感材料；按照熔融沉积、黏弹性墨水沉积、粉末烧结熔化、还原光聚合和材料喷射的制造原理分别阐述了多种传感器的材料选择、成型特点，并对制造方法进行总结分析。虽然3D打印制造柔性传感器件存在着缺乏行业标准及多种类打印材料等问题，但经过不断创新与发展，3D打印将成为柔性传感领域极佳的制造手段。     

客车涂装底层材料配套性分析

针对南方客户在使用我司客车一段时间后，车身涂层不同程度出现了起泡的质量问题，进行了现场查看，发现起泡位置在车身左右侧蒙皮，且发生在涂层最底层。初步分析原因是热镀锌板+阴极电泳漆 +原子灰三者之间配套存在问题，通过热镀锌板 +阴极电泳漆 +原子灰三者之间的耐高温 80 ℃配套试验，以及室外曝晒试验，得出镀锌板表面是否钝化、电泳漆膜致密程度和原子灰苯乙烯含量是造成涂层底层起泡的主要原因。为了控制涂层起泡问题，重新修订了我司原子灰、镀锌板、电泳漆的技术标准以及部分工艺文件。     

Micro-structural study of Yaozhou celadons (Tang to Yuan Dynasty): probing crystalline and glassy phases

The Yaozhou kiln complex is a representative production center of ancient northern China, famous for the celadon production. In this work, bubbles, glassy matrix and residual crystals of celadon glazes produced from the Tang to Yuan Dynasty were analyzed by using optical microscopy, Raman spectroscopy and scanning electron microscopy-energy dispersive X-ray spectroscopy (SEM-EDS). The results revealed that the Song, Jin and Yuan productions present bigger bubble and higher area ratios of the Si-O bending over stretching modes than the Tang and Wudai productions. This is consistent with firings at higher temperatures during Song, Jin and Yuan Dynasties. It is also in agreement with the historical studies, which revealed the change from wood-firing to coal-firing during Song Dynasty. The observation of calcium phosphate in Yaozhou productions indicated that the glaze ash had been used. No iron-based particle was identified by Raman spectroscopy in the glazes of all periods. The green color is certainly due to iron ion dispersed in the glassy matrix. Our study also confirmed no significant change in glaze raw materials used for Yaozhou productions from Tang to Yuan Dynasty.     

溶液浓差能驱动的逆电渗析反应器制氢实验研究

低品位热能制氢技术首先是将热能转换为溶液浓差能，然后通过逆电渗析（RED）反应器将溶液浓差能转换成氢能。为了验证RED反应器能将溶液浓差能转换为氢能，探索关键运行参数变化对能量转换过程的影响。设计了一个由40个膜对所构成的RED反应器，以NaCl水溶液为工作溶液，NaOH水溶液为电极液的制氢系统。通过改变浓/稀溶液入口浓度，溶液过膜流速以及输出电流来考察对RED反应器产氢率、制氢效率和能量转换效率的影响。实验结果发现，浓/稀溶液入口浓度，过膜流速变化均会影响RED反应器的输出电流。在外电路短接条件下，输出电流越大，反应器产氢率和制氢效率越高，但能量转换效率越低。     

Co-N-C催化剂的制备及“一锅法”合成N-亚苄基苯胺

以甲酰胺为氮源和碳源，乙酸钴为钴源，采用预先缩合/高温焙烧两步法制备了一系列Co-N-C催化剂，利用XRD、TEM、N₂吸附-脱附以及XPS等表征了催化剂结构，考察了催化剂用于硝基苯与苯甲醇“一锅法”合成 N-亚苄基苯胺的催化性能及其稳定性。结果表明，焙烧温度和掺杂氮元素对Co-N-C催化剂性能影响显著，催化剂Co-N-C/800具有最好的催化性能，0.6 MPa氮气气氛下，温度140℃，反应12 h，硝基苯转化率达99%，N-亚苄基苯胺选择性达99%，催化剂重复使用5次，其活性无明显下降。     

Grain size effect on microwave dielectric properties of Na2WO4 ceramics prepared by cold sintering process

In this work, cold sintering was adopted to prepare Na₂WO₄ ceramics with different grain sizes ranging from 0.632 μm to 17.825 μm. Their microstructures, complex impedance, and microwave dielectric properties were studied in-depth. It was found that samples with relative densities higher than 92% can be successfully synthesized by cold sintering process at a low temperature of 240 °C. However, their electrical properties have strong dependence on the grain size. Specifically, the resistance of grain boundaries decreases dramatically with the increase of grain sizes, while the quality factor has a positive correlation with the grain sizes of Na₂WO₄ ceramics. Excellent microwave dielectric properties, including permittivity = 5.80, Q × f = 22,000 GHz, and TCF = −70 ppm/°C, are obtained for Na₂WO₄ ceramics with a grain size of 4.477 μm prepared by cold sintering process.     

The Adhesion‐Enhanced Contact Electrification and Efficiency of Triboelectric Nanogenerators

In the present work, the contact electrification of polymers that differ in adhesion strength is studied. Electrical current is measured along with adhesion in macroscale contacting‐separation experiments. Additionally, local adhesion and roughness are studied with atomic force microscopy to get deeper insight into relations between surface properties and electrification. Measurements reveal that higher surface charge is formed on more adhesive surfaces, thus confirming covalent bond cleavage as a mechanism for contact electrification of polymers. Investigated materials possess enhanced contact electrification making them attractive candidates for the conversion of mechanical energy to electrical in triboelectric nanogenerator devices.     

基于梯度提升决策树的车轮轮缘厚度磨耗预测

轮对在列车走行过程中起着导向、承受以及传递载荷的作用，其踏面及轮缘磨耗对地铁列车运行安全性和钢轨的寿命都将产生重要影响。根据地铁列车车轮磨耗机理，分析车轮尺寸数据特点，针对轮缘厚度这一型面参数，基于梯度提升决策树算法构建轮缘厚度磨耗预测模型。在该模型的基础上，任意选取某轮对数据进行验证分析，结果表明：基于梯度提升决策树的轮对磨耗预测模型具有较好的预测精度，可预测出1~6个月的轮缘厚度变化趋势范围，预测时间范围较长，可为地铁维保部门对轮对的维修方式由状态修转为预防修提供指导性建议。